NovaStar LCT Smart
blog ·

The Art Of Control · NovaStar LCT Smart

Priced at $0
While heading the profit of my counsel, avail yourself also of any helpful circumstances over and beyond the ordinary rules.~ Sun Tzu
                 
NovaStar LCT Smart · configuration software

LCT Smart

· no charge
NovaStar LCT Smart · configuration software

LCT Smart

· hot backup

Paradoxically, LCT Smart doesn't require brilliance.

But you'll still want to follow the instructions. At least until our AI-powered Overlords take over.

Pixels

NovaStar's LED Configuration Tools begin by requesting the number of horizontal and vertical pixels in each cabinet or panel that makes up the display. If you don't happen to have that number on hand, calculate (1000/pixel pitch) * the row length. Or just start counting...

Dimensions

The configuration parameters also include the overall dimensions of the display as determined as a multiple of the pixels defined in the receiving cards. Enter the number of rows and columns and LCT works out the rest. Select one of the preset data flow icons that reflect your cabling.

Viewing

Manage the calibration of your reds, greens and blues that make up a pixel, a panel or a display using online or offline tools to upload files, set and save, adjust or erase or reset calibration coefficients. Odds are you'll probably enjoy the results more than the work, but that's life.

Performance

NovaStar LCT does everything you might ask of configuration software. We are currently on version 5 so there is a wealth of knowledge and experience that has brought us to this point. LCT is just the nuts and bolts to get you up and running. Just be sure to read the manual.

Power

LCT is happy on any modern PC that runs a current copy of Windows. If your display is happier on a Mac, LCT Smart is available for OSX. Having invested in a gorgeous new LED that spans your lobby or welcomes your customers, maybe it is time for some fresh hardware.

Installation

Download LCT from our links below and open up the .zip file on your desktop. Then just double-click through to locate the application file and then follow the prompts from there to allow the serial driver to be installed or otherwise updated on the system hard drive.

Specifications · NovaStar LCT Smart

Executive position wanted. Permanent or temporary.
Therefore, in your deliberations, when seeking to determine the military conditions, let them be made the basis of a comparison. ~ Sun Tzu
                 
Version V3.4.0 V3.4.0
Installation
 
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
 
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
NovaStar LCT Smart · software installation instructions
 
Software · Manuals
 
NovaStar LCT
 
NovaStar LCT Smart
 
NovaStar Viplex
 
Instructions
 
LCT Smart is the new generation of screen configuration software from NovaStar.
 
With Smart, NovaStar has made significant advances towards creating an intuitive software for setting up complex LED Display designs, both online and offline. The software is compatible with recent versions of Windows and with OSX.
 
We have created a quick reference guide for Nova Smart LCT that should provide answers for most every question that comes up during an installation. We otherwise encourage you to download the manual for a comprehensive solution.

Key Features

  • Screen configuration like building blocks
  • Angles of image rotation supports the multiples of 90° (working with the Armor series receiving cards)
  • Supports 360° free image rotation (working with the MCTRL R5)
  • Supports 18bit+ and ClearView.
  • Supports receiving card program and configuration information readback
  • Supports the monitoring service and platform
  • Supports seam brightness adjustment
  • The functions of video controllers can be set on V-Sender
  • Supports cabinet brightness and chroma adjustment in batches
  • Supports hot backup
  • The canvas can be exported as an image
  • Windows, OS X

Configuration List

  • Series MCTRL
  • Series Professional
  • Series VX
  • Series MRV
  • Series A8S
On the LCT Smart start page, create an online or offline project, or open an existing project to enter the screen configuration page.

Start Page

  • Project
  • 🗀New  🗀Open  🗀Save  🗀Save As  🗀Export  🗀Language
  • New allows the user to create a new project.
  • Open allows the user to open an existing project.
  • Save allows the user to save a project.
  • Save As allows the user to save a project under a new name.
  • Export allows the user to export a project.
  • Language allows the user to set the language.
  • Device
  • 🗀Reconnect  🗀Refresh  🗀Hot Backup  🗀Seam Brightness  🗀Mapping
  • 🗀Test Pattern  🗀Factory Reset  🗀Brightness Adjustment  🗀Batch
  • Reconnect Device allows the user to search for and reconnect a device, update hardware information and save it to the current file.
  • Hot Backup allows the user to backup between the devices and backup between the Ethernet ports of a device.
  • Seam Brightness adjusts the seam brightness of the LED display.
  • Mapping displays the receiving card number and Ethernet port information on the cabinets.
  • Test Pattern verifies the display effect of cabinets.
  • Factory Reset resets the parameters to factory defaults.
  • Brightness Adjustment adjusts brightness of the screen.
  • Batch adjusts cabinet brightness and chroma in batches.
  • Edit
  • 🗀Cabinet Management  🗀Cabinet Connection  🗀Delete Connection  🗀Advanced
  • 🗀View  🗀Send  🗀Save to Hardware (online operation)
  • Cabinet Management allows you to add cabinets and set cabinet size.
  • Cabinet Connection allows you to choose the cabinet connection type.
  • Delete Connection removes the lines between cabinets.
  • Advanced allows you to set cabinet display status in the editing area and the snapping mode.
  • View includes front view and rear view.
  • Sends the display configuration file to hardware devices.
  • Save to Hardware sends and saves the screen configuration file to hardware devices.
  • Monitor
  • 🗀Real-Time Monitoring  🗀BER Detection  🗀Version Information  🗀Monitoring Configuration
  • Real-Time Monitoring monitors cabinet status in real time.
  • BER Detection detects data packet loss during the communication between receiving cards.
  • Version Information displays the Ethernet port information and program version information of the controllers and receiving cards.
  • Monitoring Configuration allows you to configure the parameters to be monitored.
  • Help
  • 🗀Test Tool  🗀User Manual  🗀About
  • Test Tool opens a preview window on the desktop to view the result of the test.
  • User Manual opens the Smart manual.
  • About identifies the software information.
LCT Smart is available in German, French, Russian, Spanish, Chinese and English.

Language

  • Select your preferred language from the option box.
On the LCT Smart start page, create an online or offline project, or open an existing project to enter the screen configuration page.

4.1 User Interface

  • Canvas Properties
  • 🗀Grid Color  🗀Grid Width  🗀Grid Height  🗀Screen Name  🗀Disable Edit
  • Grid Color allows the user to edit the grid color of the canvas.
  • Grid Width allows the user to set the grid width of the canvas.
  • Grid Height allows the user to set the grid height of the canvas.
  • Screen Name allows the user to set the screen name.
  • Disable Edit allows the user to disable all the actions in the canvas.
  • Screen Color Settings
  • 🗀Grid Color  🗀Brightness  🗀Gamma  🗀Customize Color Temperature
  • Brightness allows the user to set the brightness of the display.
  • Gamma allows the user to modify the gamma settings.
  • Customize Color Temperature allows the user to modify the RGB settings.
  • Device Properties
  • 🗀Manufacturer  🗀Type  🗀Device  🗀Port Name  🗀Connection  🗀Mapping Position  🗀Position
  • Manufacturer is the display manufacturer identified in the drop down menu.
  • Type allows the user to select the module size.
  • Device allows the user to select the model of NovaStar controller.
  • Port Name allows the user to select the port.
  • Connection identifies the sequence of the sending card, Ethernet port number and the receiving card.
  • Mapping Position sets the position of the top left cabinet on the LED display.
  • Position sets the position of the top left cabinet on the canvas.
  • Loading Capacity Usage
  • If set to Auto Connect, the cabinets beyond the loading capacity of the Ethernet ports cannot be connected.
  • If manually connected, the cabinets beyond the loading capacity of the Ethernet ports can be connected.
  • The Loading Capacity Usage section displays the usage of the loading capacity of Ethernet ports.
  • Blue: Denotes the loading capacity is normal. When the loading capacity of the connected cabinets is within that of the Ethernet ports, the progress bar shows blue.
  • Red: Denotes the loading capacity is beyond the limit. When the loading capacity of the connected cabinets exceeds that of the Ethernet ports, the progress bar shows red.

4.2 New Projects

In the Function section of the start page, click Create Offline Design to enter the Create a new project page.
  • Function
  • 🗀Project Name  🗀Device Selection  🗀Cabinet Selection  🗀Screen Size  🗀Maximum Load  🗀Connection Type
  • Project Name allows the user to name the project and choose a save path for the project.
  • Device Selection allows the user to select a video controller.
  • Cabinet Selection allows the user to select the manufacturer and type of the cabinets.
  • Screen Size allows the user to set the columns and rows of the cabinets.
  • Maximum Load shows the maximum screen width and height that can be loaded by the device.
  • Connection Type allows the user to select the connection type of the cabinets or Auto Connect.
  • Cabinet Management
  • 🗀Export Selected Cabinets  🗀Export All  🗀Delete  🗀Add
  • Export Selected Cabinets allows the user to export one or more cabinet files.
  • Export All allows the user to export all the cabinet files.
  • Delete allows the user to delete cabinet files.
  • Add allows the user to import and add cabinet files.
  • Creating Modes
  • Normal Mode allows the user to edit the project name, choose the save path, and select the cabinet
  • Smart Mode

4.3 Screen Configuration

After an offline project is created, you will enter the Edit page.
  • Adding Cabinets
  • Select device type and Ethernet port type.
  • In the Cabinet Management section, add batches of cabinets.
  • In the Cabinet Management section, add single cabinets.
  • Select cabinets from the canvas using click and drag.
  • Cabinet Connection
  • Connecting Cabinets
  • Before configuring the screen, you need to connect the cabinets. SmartLCT offers two connection methods.
  • Auto connect
  • On the Create a new project page, after you have selected Auto Connect, the cabinets will be automatically connected while you adding them in the canvas. If the loading capacity of the cabinets loaded by a single Ethernet exceeds the allowed loading capacity of that Ethernet port, auto connection will stop.
  • Manual connect
  • Add cabinets in the canvas and select the target cabinets. Then, in the Cabinet Connection section of the tool bar, choose a cabinet connection type. If the loading capacity of the cabinets loaded by a single Ethernet exceeds the allowed loading capacity of that Ethernet port, the connection will stop.
  • Add cabinets in the canvas. Then, click to select the center of the first target cabinet and then move to the center of the second cabinet, and continue.
  • Choose Edit > Advanced to enable or disable Auto Connect.
  • Grouping Cabinets
  • In the canvas, select the target cabinets and right-click to choose Group.
  • In the Properties section, set the name, color and position for the grouped cabinets. The grouped cabinets will be edited as a whole.
  • Deleting Cabinet Connection
  • Select the target cabinets and right-click to select Delete Connection to remove the connection between the cabinets.
  • Setting Cabinet Offset
  • After you have added cabinets and connected them, a dotted rectangle surrounding the cabinets will appear. The size of the dotted rectangle denotes the loading capacity of the connected device.
  • Select the arrow right to a cabinet and change its position relative to the dashed box.
  • Rotating Cabinets
  • Select the rotate icon to set the angle of rotation of the cabinets to the target position.

4.4 Sending Configuration Information

  • Select the paper airplane icon and select yes in the confirmation box.
  • Select the matching device that is online.

4.5 Other Operations

  • Adding Devices
  • At the bottom left of the Device section, select the plus icon to open the Add Devices dialog box.
  • Select the device type and number to be cascaded and select Add.
  • Hot Backup
  • 🗀Device  🗀Hot Backup
  • The hot backup includes backup with the device (Ethernet port backup) and backup between devices.
  • Hot backup is only available for the devices with the same communication ports.
  • After device backup is set, the Ethernet ports of the backup device will be the backup of the corresponding ports of the master device. The backup relations cannot be crossed and removed.
  • Backup Within the Device
  • Add a device to the editing area.
  • When the Ethernet ports are backed up, click at the top right of the device to remove the backup.
  • Click X between two Ethernet ports to delete the line.
  • Click X at the top right of the device to delete the device.
  • Backup Between Devices
  • Add devices that requires backup to the editing area.
  • Drag a device onto another device, and the backup can be done automatically. Or click the small triangle in the right side of the device, drag to the small triangle of the other device and click to complete the backup.
  • When the backup is done, the icon appears on the line between the two devices. Click this icon to switch between master and backup.
  • Click X at the top right of a device to delete the device.
  • Click the highlighted X at the top right of the dashed box to remove the backup.

5.1 User Interface

  • Canvas Properties
  • Select a blank area of the canvas and edit canvas properties in the Canvas section.
  • 🗀Grid Color  🗀Grid Width  🗀Grid Height  🗀Screen Name  🗀Disable Edit
  • Grid Width allows the user to set the grid width of the canvas.
  • Grid Height allows the user to set the grid height of the canvas.
  • Screen Name allows the user to set the screen name.
  • Disable Edit allows the user to disable all the actions in the canvas.
  • Screen Color Settings
  • This is used to set color parameters of the screen.
  • 🗀Gamma  🗀Color Temperature  🗀Enable 18-bit Mode  🗀Enable ClearView  🗀Calibration Type  🗀Color Gamut Setting
  • Gamma: Supports gamma.
  • Color Temperature: Supports custom brightness and color temperature.
  • Enable 18-bit Mode: Supports 18 bit grayscale mode.
  • Enable ClearView: Supports ClearView.
  • Calibration: Supports calibration type selection.
  • Color Gamut Setting: Supports custom color gamut.
  • PAL NTSC: Supports PAL or NTSC.
  • Device Properties
  • Select a cabinet. The properties of the device is displayed in the Properties section.
  • 🗀Manufacturer  🗀Type  🗀Device  🗀Port Name  🗀Connection  🗀Mapping Position  🗀Test Pattern
  • Manufacturer: Default.
  • Type: Default
  • Device: NovaStar series.
  • Port Name: USD Hub
  • Connection: Shows sending card #, Ethernet port # and receiving card #.
  • Mapping Position: Position of the selected cabinet's top-left corner on the LED display.
  • Test Pattern: Verifies the display effect of the screen.
  • When the connected device supports rotation function, the center and angle of rotation can be set in the properties of the device to achieve full rotation of the LED display
  • Advanced Properties
  • On the Advanced tab page, you can set the pre-stored image and the startup screen status.
  • 🗀Choose Image  🗀Effect Settings  🗀Function Settings  🗀Disconnect Cable  🗀No DVI Signal
  • Choose Image: Browse for image file.
  • Effect Settings: Choose from tile, stretched or centered.
  • Function Settings: Enable or disable the startup screen function.
  • Disconnect Cable: Set what is displayed when the cable is disconnected.
  • No DVI Signal: Set what is displayed when there is no DVI signal.

5.2 New Projects

  • Run Smart and refresh the device list and screen list.
  • In the Function section, select Create Online Design to create a new project page.
  • 🗀Project Name  🗀Cabinet Selection  🗀Screen Size  🗀Maximum Load  🗀Connection Type
  • Project Name: Name the project and choose a save path for the project.
  • Cabinet Selection: Select the manufacturer and type of the cabinets.
  • Screen Size: Set the columns and rows of the cabinets.
  • Maximum Load: The maximum screen width and height that can be loaded by the device.
  • Connection Type: Select the connection type of the cabinets.

5.3 Screen Configuration

  • After an online design is created, the edit page will be displayed.
  • If the system is connected with receiving cards, it can read the cabinet size automatically.
  • Select an Ethernet port type.
  • In the Cabinet Management section, click the cabinet icons to add single or batches of cabinets.

5.4 Seam Brightness Adjustment

  • First configure the LED display and then navigate to the Seam Brightness Adjustment page
  • 🗀Module Mode  🗀Cabinet Mode  🗀Select Border  🗀Clear Status  🗀Keyboard Shortcuts
  • Module Mode: Split the added cabinet into different areas (modules).
  • Cabinet Mode: Recover the split cabinet.
  • Select Border: Click-and-drag to choose the cabinet or click to choose horizontal borders of the cabinet.
  • Clear Status: Clear selected status.
  • Keyboard Shortcuts: Set keyboard shortcuts and use them for cabinet mode selection and borders settings.
  • Tool Bar
  • 🗀Show Screen Window  🗀Show Dashed Box  🗀Show Number  🗀Calibration Type
  • 🗀Image Quality Adjustment  🗀Screen Display Position
  • Show Screen Window: Show or hide display window.
  • Show Dashed Box: Show or hide dashed box of the selected borders.
  • Show Number: Show or hide serial number of the display window.
  • Calibration Type: Close calibration, chroma and brightness calibration.
  • Image Quality Adjustment: Testing color on the display window.
  • Screen Display Position: Switch position of the display window.
  • Seam Brightness Parameter Adjustment
  • 1. Choose Device > Seam Brightness to enter the seam brightness adjustment page.
  • 2. Select the target border, and the border will become blue.
  • 3. Choose precision of the adjustment.
  • 4. Drag the slider next to the Selected Area Parameter Adjustment to adjust seam brightness parameters, and the borders will become green.
  • 5. Type “admin” to access the factory area and user area settings page.
  • Save to Factory Area: Save seam brightness adjustment parameters to the factory area of the receiving card. These parameters will be used for maintenance after the cabinet is returned to factory.
  • Save to User Area: Save seam brightness adjustment parameters to the user area of the receiving card. These parameters will be used for on-site screen adjustment.
  • Load Factory Area: Restore seam brightness adjustment parameters to the parameters last saved in the factory area.
  • Load User Area: Restore seam brightness adjustment parameters to the parameters last saved in the user area.
  • Save to HW: Save seam brightness adjustment parameters to the sending device.
  • Save: Save the seam brightness adjustment parameters.
  • Save seam brightness adjustment parameters to the sending device.

5.5 Batch Adjustment

  • This function is used to adjust the brightness and chroma of cabinets of different batches in order to ensure the images are displayed uniformly on LED screen.
  • First, configure the display and save the configuration parameters to hardware.
  • 🗀Tool Bar  🗀Editing Area  🗀Batch Editing Area  🗀Brightness Adjustment Area  🗀Chroma Adjustment Area
  • Tool Bar: Import: Import the batch adjustment parameter file, Save, Display, Calibrate, Switch and Save To Hardware.
  • Editing Area: Edit the status of cabinets or modules.
  • Batch Editing Area: Select to add a batch.
  • Brightness Adjustment Area: Adjust cabinet brightness parameters.
  • Chroma Adjustment Area:Adjust cabinet chroma parameters.
  • 1. Select a target batch.
  • 2. In the editing area, select the target cabinets or modules, and then click Add to Sample Area.
  • 3. Adjust chroma and brightness.
  • 4. Select Apply Adjustment.
  • 5. Select Save to HW.

5.6 Monitoring

  • First refresh the monitoring information of current system.
  • 🗀Real-Time Monitoring  🗀BER Detection  🗀Version Information  🗀Monitoring Configuration
  • Real-Time Monitoring: Monitors the real-time status of the hardware devices such as receiving cards and function cards.
  • BER Detection: Detects data packet loss during the communication between receiving cards.
  • Version Information: Displays the device type, communication port status major version and other versions of the controllers and receiving cards.
  • Monitoring Configuration: Configure the information to be monitored.

5.7 Sending Configuration Information

  • Select the paper airplane icon and select OK in the confirmation box.

5.8 V-Sender

  • V-Sender allows you to set the status of the current device and operate the device on the PC.
  • 🗀Reconnect  🗀Refresh  🗀Reset  🗀Save  🗀Update  🗀Test  🗀Monitoring  🗀Language
  • Reconnect: Reconnect the device after the device went offline.
  • Refresh: Refresh the device information.
  • Reset: Reset to factory settings.
  • Save: Send current device information to the hardware device and save it.
  • Update: Update the firmware version of current controller device.
  • Test: Test the display effect of the images displayed on LED screen.
  • Monitoring: Set the temperature and voltage ranges for normal operating of current controller device.
  • Language: Set the language of current page.

5.9 Other Operations

  • Smart supports the Mapping function.
  • Under Device > Mapping the receiving card numbers and Ethernet port information are displayed on the cabinets of the screen.

6.1 Building Screens Like Building Blocks

  • 1. In the Device section, select a device and Ethernet port.
  • 2. In the Tool bar, select Edit and then Cabinet Management
  • 3. Select the Canvas to add cabinets.
  • 4. Select one or multiple cabinets and move the mouse to change the cabinet position to build different layouts.

6.2 Rotating in 90° Increments

  • Connect those receiving cards or controllers that support rotation.
  • 1. On the canvas, select the target cabinets.
  • 2. In the property area, select Reorient to select the angle of cabinet rotation.

6.3 Full 360° Rotation

  • Connect the controller MCTRL R5 to Smart and the rotation function can be enabled.
  • Rotation of a Single Cabinet
  • 1. Select Rotate and then the cabinets. A rotating bar appears on each of the cabinets.
  • 2. Select any of the rotating bars and drag the mouse. The cabinet rotates around its rotation center.
  • 3. Or set the rotation center and angles of rotation in the property section on the right.
  • Rotation of a Group of Cabinets
  • 1. Select Rotate and the cabinets.
  • 2. Right-click the cabinets and select Group.
  • 3. Select the grouped cabinets. A rotating bar appears on each of the cabinets.
  • 4. Click the rotation bar and drag the cabinets. The group of cabinets rotates around the rotation center.
  • 5. Or set the rotation center and angles of rotation in the property section on the right.

6.4 LED Display Test

  • Select Tools and then Test Tool to enter the display test tool page or receiving card test page.
  • 🗀Window  🗀Pure Color  🗀Gradient  🗀Grid  🗀Orientation  🗀Help  🗀About
  • Window: Set window position and size, or hide the window.
  • Pure Color: Set window color (pure color), gray scale and refresh rate.
  • Gradient: Set the gradient color and levels of the window.
  • Grid: Set grid and color and other parameters of the window.
  • Orientation: Set module size and the number of modules loaded by the scanning board. Detailed settings are shown in the figure below.
  • Help: Keyboard shortcuts for quick operations.
  • About: Details in the box.

6.5 Update and Read-back of Receiving Card Configuration Parameters

  • 1. Select the target cabinets on the canvas.
  • 2. Right-click to select Read back parameters/Update receiving card parameters to read back or update local receiving card configuration parameters.

6.6 Read-back of Controller and Receiving Card Information

  • Select the refresh icon next to the corresponding controller or receiving card to read back the model, communication port and hardware version of the current controller or receiving card.

6.7 Receiving Card Program Upgrade

  • First, save the upgrade package of receiving card firmware program to the local PC.
  • 1. In the canvas, select the target cabinets to enter the Properties tab page on the right.
  • 2. Select the Upload icon next to the Program Version.
  • 3. Select the path of the upgrade package to upgrade the firmware program.

6.8 Controller Program Upgrade

  • Save the upgrade package of the controller firmware program to the local PC and then enter V-Sender.
  • 1. Select V-Sender.
  • 2. Select Update or select the Properties tab and the upload icon next to Program Version.
  • 3. On the Firmware Upgrade window that appears, select the path of the upgrade package.
  • 4. Select Update.

6.9 Exporting Screen Configuration Information as Image

  • Select Project and then Export
  • 1. Set export parameters and information.
  • 2. Click Export to export the screen configuration image to the local PC.
 
Fine Print
 
Specifications NovaStar and Telematics reserves the right to change any specifications without prior notice.
 
Factory Warranty Faulty components to be repaired or exchanged for 3 years from the date of shipping.

The Sales Pitch

So here's the deal...
Energy may be likened to the bending of a crossbow; decision, to the releasing of a trigger. ~ Sun Tzu
                 

About Telematics

Telematics is a federally-incorporated company based in Vancouver since 2000. Our global partners manufacture innovative LED display panels, cabinets, curtains, interactive video floors and the systems that control them. We distribute the world's most advanced touch skins and rear projection films that turn any window into a massive display.
 
Our high-volume relationship with our manufacturers and low corporate profile allows us to provide aggressive pricing and personalized service to a world-wide network of principals and project managers in the audio-video and digital signage industry. We also sell directly to businesses and individuals who select and install their own systems with the assistance of local tradesmen and engineers.

Our Manufacturers

NovaStar is one of the leading LED display solutions providers in the world, with product lines that include LED display synchronous and asynchronous control systems, point-by-point calibration and cloud-based information publishing and management.
 
The Beijing Olympic Games, Tienanmen Celebration for the 60th Anniversary on National Day,Shanghai World Expo, Guangzhou Asian Games, Xi'an International Horticultural Expo, Games for University Students and other large-scale events all relied on control systems are provided by Nova.
 
Through constant innovation, NovaStar now holds more than 20 proprietary intellectual property rights in LED display control, cloud computing and other fields.
 
NovaStar has been awarded the Xi'an Award for Science and Technology and the Shaanxi Award for Science and Technology.

Our Customers

For 18 years we have developed business relationships with thousands of people from every corner of the world.
 
Many are audio visual professionals and consultants who need to source premium equipment for their clients. Others are architects and designers looking for solutions to create LED walls or interactive floors. And some are end-users prepared to take on the challenge of setting up their own digital displays.
 
In each case, we provide our customers with the answers they need and endeavor to offer solutions that are affordable, effective and reliable.
 
And we always keep their secrets to ourselves.

Our Cool Videos

A video is worth a thousand likes.
The onrush of a conquering force is like the bursting of pent-up waters into a chasm a thousand fathoms deep.~ Sun Tzu
                 
     

S5 Box

Pricing · NovaStar Control

We respect the value of your time. Use these numbers to ballpark the costs for your project. Then call us for a quote.
Now the general who wins a battle makes many calculations in his temple ere the battle is fought. ~ Sun Tzu
                 
Series MCTRL
MCTRL 4K 4995 /unit
MCTRL R5 2710 /unit
MCTRL 660 Pro 1179 /unit
MCTRL 660 699 /unit
MCTRL 600 530 /unit
MCTRL 300 315 /unit

Cardboard Packaging
Ground · Air Freight

Factory Warranty · Three Years
Series Taurus
TB8 750 /unit
TB6 490 /unit
T6 400 /card
TB3 389 /unit
T3 299 /card

Cardboard Packaging
Ground · Air Freight

Factory Warranty · Three Years
Series VX
VX6S 1888 /unit
VX4S 1650 /unit
VX4U 1533 /unit
VX2U 1060 /unit

Cardboard Packaging
Ground · Air Freight

Factory Warranty · Three Years

Checklist

Don't drive yourself crazy trying to figure out the right series and the correct specifications and dimensions for your project. Just contact our offices and in ten minutes we can review everything and find out what works best for the space and the budget. There...I'm feeling better already.

Order

If you are like everyone else, you will leave this part to the last possible moment. Then we will share in your stress and jump through every imaginable hoop to meet your evolving schedule. We strive to have the most popular NovaStar products in stock at all times, but orders are first-come first-serve.

Ship

We can ship your order by air or ground as your budget and time allows. Shipping and Customs schedules can be estimated, but are external variables that are outside of our control. Allow plenty of time for unexpected delays. You would not believe how many National Holidays are observed in China. Seriously.

Install

Your installation will include a PC for content and a NovaStar controller to direct that content to the display. There will be power and data cables to hook everything up and a frame or support beams to mount your display. If you need assistance with this, Telematics can often suggest a local partner.

Service

NovaStar provides their full technical expertise to assist Telematics and our clients with any issues where we have requested their assistance. Most problems are diagnosed and resolved very quickly using remote access software, Skype and webcams or a simple exchange of emails and phone calls.

Warranty

NovaStar supports their products with a comprehensive 3-year factory warranty that is completely free of fine print from the Law Firm of Obfuscate, Muddle and Flummox, and is instead defined by simply keeping our customers' confidence by standing behind each and every product they make.

Contact · Telematics Canada

Politely awaiting your call. It's a Canadian thing...
Sun Tzu said: We shall be unable to turn natural advantage to account unless we make use of local guides. ~ Sun Tzu
                 

Telematics Canada

375 Water Street, Suite 200
Vancouver, BC V6B 0M9
Canada


8:00 am to 8:00 pm

(1) 604.331.8795
This email address is being protected from spambots. You need JavaScript enabled to view it.
telematics.canada

https://www.telematics.ca
Telematics Canada (2000)

Michael Wolf

Canada · USA · International
(1) 604.331.8795
(1) 604.209.3955 (text me!)

Director

This email address is being protected from spambots. You need JavaScript enabled to view it.

Alicia Mottus

Administration
(1) 604.331.8795
 

Director

This email address is being protected from spambots. You need JavaScript enabled to view it.